How to set a comfortable bicycle riding position | BikeGremlin (2024)

Unless a bicycle frame is by “three sizes” too big/small, it can usually be set to better suit a rider’s comfort. This post gives instructions for setting up a comfortable riding position, i.e. bicycle fitting. For a shorter, simpler explanation, more suitable for beginners, read the post: Setting up comfortable riding position.

If you have any questions (or additions and corrections), please use the BikeGremlin forum:
www.bikegremlin.net

Table Of Contents (T.O.C.):

TL/DR

0. Intro
1. Contact points
2. Saddle angle
3. Setting up seat height
4. Horizontal saddle position – for-aft
5. Handlebars: height and reach
6. Videos about bike-fitting

TL/DR

Briefly put, here I’ve explained how you can make your bike be more comfortable by adjusting saddle and handlebar height (and tilt – along with some other minor tweaks).

The main point is to start with the saddle – and adjust your handlebars afterwards. It’s straightforward and yields great results.

I’ve added photos to help you see & understand – and tackled the most common bike-fitting mistakes.

– T.O.C. –

0. Intro

This is post that explains how totune bicycle riding position so that it is functional and comfortable. Before setting up a seating position, one needs to find a correct size frame. Post about finding optimal sized frame can be read here:

How to choose a correct frame size

Riding position should be such that it is comfortable and enables the rider to pedal efficiently and to easily control (steer) the bicycle. It sounds simple, and it is, but some small things should be taken into consideration and can make a big difference.

– T.O.C. –

1. Contact points

Things that make riding position are contact points. Places where rider comes in contact with the bicycle: seat, pedals and handlebar.

The significance of contact points is clearly shown in the picture below. Small, folding bicycle has seat post and handlebars lifted high enough, so itprovides a seating position similar to one on a much larger bicycle.

So, for comfortable and efficient riding, contact points need to be set to appropriate distances from each other. These distances are determined by rider’s dimensions: leg and torso length. They are also influenced by the type of preferred position: whether it’s an aggressive racing position, or more relaxed, upright position for cruising.

Speaking of contact points, this is the correct way to place a foot on a pedal:

Ball of the foot should carry the weight on the pedal. Leaning with the middle of the foot, or with the toes is not optimal foot positioning.

– T.O.C. –

2. Saddle angle

Saddle should be parallel to the ground.This should be done first. Mostmen like saddle nose tilted for a degree or two up, most women prefer a degree or two down, but level is a good starting point. It can later be tweaked.

If the saddle is tilted too much forward, rider will start sliding forward, putting too much pressure on the hands and bars. Making bars uncomfortable.

– T.O.C. –

3. Setting up seat height

This is the best starting point. Seat height is first roughly determined by sitting on the saddle, placing heels on the pedals and straightening leg. Pedal shouldn’t be too low, or too high to lift the rider off the saddle. Hips should be parallel to the ground – not tilted to either side.

When doing this, one should lean against a solid object, and hold a brake to keep the bike in place.

Many beginners place their seats too low, so they can reach the ground when standing still. This was possible (with correct seat hight) on older bicycles. From 1980s, frames are made so that BB is higher. This enables crossing obstacles and leaning in turns more, without pedals hitting the ground. However, it makes impossible putting both feet on the ground when seated, not if the saddle isn’t set too low.

Riding with the saddle too low can cause knee pain and health problems. It’s the equivalent of walking in a crouched position all the time – exhausting and inefficient.

Too high a saddle causes other problems. Foot will move downwards when in the bottom of a stroke, in order to reach the pedal. Hips will also rock from side to side. Too much pressure will be exerted on the back and crotch – because legs aren’t carrying much weight.

How to find the optimum? After finding a starting point with the heel method. Increase height by one cm and go for a long ride. When you reach the point of too much (hips start rocking, pressure on the saddle, feet move downwards in order to reach pedal in the bottom of a stroke): lower the saddle by half a centimetre. “You don’t know what is enough, until you find out what is too much”. 🙂

The heel method itself is precise enough for most recreational cyclists.

Cyclists that like pedaling fast (with a high cadence), prefer the saddle to be a bit lower than the height set up using the previously explained method – by 3 to 8 mm. That is individual and comes with trying and experience. Still, “heel” method is an OK starting point.

– T.O.C. –

4. Horizontal saddle position – for-aft

Seat horizontal position is tuned so that whencranks are parallel to the ground, a pendant hanging from the bottom of the knee cap goes straight through the pedal axle. Make sure that feet are placed correctly on the pedals (explained at the end of the contact points chapter). This (starting) position is also known as KOPS (knee over pedal spindle).

When this is done, seat height should be checked once more with heel method (because for-aft position influences the distance to the pedals). If the saddle is moved. After that, check once more for fore and aft position. That’s how with several iterations, perfect position can be tuned.

Just to note that KOPS is a good starting position. For aggressive riding (or for chronometer), saddle will be moved a bit more forward, while a laid back riding style will be better with the saddle a few cm behind the KOPS position. Also, it depends on personal preference. However, KOPS is a very good starting position, before tuning the rest of the bike (handlebars etc.).

It is wrong to try adjusting the handlebars distance by moving seat forwards and back. Handlebar distance is changed using different stem lengths. Saddle position is determined relative to the BB and pedals, like explained, nothing else.

If the saddle is moved too far back, it will make a crunched position, with bars too far ahead.

If the saddle is too far ahead, there will be too much pressure on the hands. Like trying to lean ahead, while standing leaned with one’s back against the wall.

– T.O.C. –

5. Handlebars: height andreach

When the saddle is fine tuned, all that’s left is to set up the last contact point: handlebars.

Handlebar reach, i.e. distance from the seat to the handlebars, depends on rider’s torso and arms length. The distance should be such that hands are comfortably holding the bars, with a slight bend at the elbows. Without too much stretching, cramping at the back or at the shoulders etc.

When the saddle is adjustedproperly, handlebars should be set according to personal preference. As long as handlebars are at least as wide as the rider’s shoulders, the rest is more-less subjective. Some like high, upright riding position, some prefer more aero. As long as handlebars can be reached with hands slightly bent at the elbows, without uncomfortable stretching to reach, or too much bend at the elbows, it is fine.

For those with threadless stems, that want handlebars a bit higher than their steering tube allows, one option is using a good quality adjustable stem, like this Ritchey 4-axis adjustable stem (Amazon affiliate link):

For a decent quality stem-riser (in case you need even more bar height), a good option is Origin8 Extra-Lift (Amazon affiliate link):

Postsabout setting up handlebars and levers (co*ckpit):

Setting up handlebar height and angle
Setting up MTB handlebars
Setting up road handlebars

– T.O.C. –

6. Videos about bike-fitting

My video explaining the basics of bicycle frame geometry and bicycle fitting:

I’ve made another video explaining the correct frame size in more detail, along with the basics of road bike fitting (link to the video on YouTube).

If you have any questions (or additions and corrections), please use the BikeGremlin forum:
www.bikegremlin.net

– T.O.C. –

The existing comments posted under this article (questions and answers) have been moved to this BikeGremlin forum thread:
https://www.bikegremlin.net/threads/setting-up-riding-position-bike-fitting-article-comments.146/