hot melt rubber (synthetic)
Offers the widest range of application flexibility available. Exhibits excellent processing performance whether manually or automatically applied. Has superior tensile strength, adhesion properties and holding force which ensures consistent, reliable seals. Hot melt adhesive will bond faster to a surface which is referred to as quick-grab or quick-stick. It typically has higher tack (will feel stickier to the touch), but is also softer. It has lower heat resistance, shear resistance, and sometimes UV resistance than an acrylic adhesive. NOTE: it is called hot melt because the adhesive is applied hot by the manufacturer and then hardens as it cools (you do not need to apply heat to the tape yourself).
natural rubber
Properties are similar to that of hot melt rubber, but natural rubber often holds where other adhesives won't (recycled fibers, dust, cold, heat and heavy loads). It provides good overall adhesion and moisture resistance.
acrylic
Offer excellent performance, especially for applications in temperatures less than 40°F and greater then 120°F. It provides excellent clarity, has high shear strength, is usually more permanent/durable even when exposed to moisture, and it ages well over extended periods in fluorescent and sunlight. Since it remains clear for the life of the application and does not yellow over time it is ideal for applications such as sealing white cartons. While it has good initial adhesion it does take 24-48 hours to cure and to achieve its maximum bond strength (has gradual adhesion buildup). Another difference between hot melt rubber and acrylic adhesive is if you fold tape over making the two adhesive sides touch the acrylic adhesive will remain attached to the carrier (e.g. paper, film) while a hot melt adhesive will stick to itself and pull off of the carrier. It is the best choice for clarity, UV resistance and aging characteristics.
silicone
Is great for extreme temperature applications since silicone adhesive can work in continuous operating temperatures from -100°F to 500°F. They also exhibit good chemical resistance, retain electrical properties, and remove cleanly with little or no residue.
zinc oxide
Zinc oxide based adhesive formula is a skin-friendly adhesive which is commonly used on sports medicine tapes.
Thickness, AKA caliper or gauge, refers to the distance from one surface of a tape backing, or adhesive, to the other.
1 mil = 1/1000 of an inch
Examples: 1/16 inch = 62.5 mils; 1/32 inch = 31.25 mils
The cut level indicates how many grams of cutting load a glove can withstand from a sharp blade before being penetrated.
Lower gauge gloves are heavier - have thicker construction, fewer stiches knitted per inch and offer less dexterity.
Higher gauge gloves are lighter - have thinner/finer construction, more stitches knitted per inch and offer more dexterity.
Gloves offered typically runs from 7 to 18 (12 and 13 are in the middle of the scale).
FAQs
Use directly from package without kneading and apply approximately 4 squares of putty per 1lb of weight.
Can you reuse poster putty? ›
This non-greasy putty stays in excellent condition over extended periods. You can use it over and over, and thanks to the innovative sleeve packaging, you can store it with ease without fear of it drying out.
Does poster putty rip paper? ›
Loctite's mounting putty pack includes 2 ounces of blue putty that's sticky enough to adhere securely to hard surfaces but not so sticky that it will tear paper posters or artwork. A convenient alternative to staples, tape, and magnets, it can be used in the home, classroom, studio, and office.
How much putty do I need? ›
Yet, on average, the coverage area putty consumption per sqm is 1.86–2.04 per sqm. If these steps seem difficult, it will be best to seek an expert painter's help to know the exact putty coverage area and cost.
What is the best adhesive for poster mounting? ›
PMA is ideal for mounting posters and photographic prints that are easily reproducable from a negative or a disk.
How do you soften poster putty? ›
Mix 1 to 2 US tbsp (15 to 30 mL) of water into your putty. Lay your putty on a flat surface, like a table or desk. Pour a few spoonfuls of water into the putty, then begin molding and kneading it with your fingers to see if it feels any softer or more pliable.
How do you remove poster putty residue? ›
Poster putty may leave an oily spot on the wall if the wall finish is porous. Clean the stain with a citrus solvent such as the kind used to remove stickers. Clean it!
Does putty ruin posters? ›
Unlike nails, tacks, and duct tape, mounting and poster putty won't leave holes or peel paint.
Does poster putty remove paint? ›
Never pulls the paint off or leave any marks. We also use it to help keep that stubborn picture on the wall straight. Kids use it to hang posters or any pictures in their rooms.
What is the best adhesive for paper posters? ›
Use either rubber cement or spray adhesive (especially designed for paper) to adhere text pages, title banners and other paper materials to the poster backing. DO NOT use white glue (Elmer's glue), paste, mucilage, glue sticks, craft glue, airplane cement, or other similar adhesives.
This convenient, ready-to-use putty bonds just about anything to slick or hard surfaces, such as wood, tile, glass, concrete, porcelain, Formica®, metal and painted surfaces. Use to fasten decorations, posters, notes and paintings. Also helps protect items from vibration damage.
Can you use putty as glue? ›
Plastic epoxy putty can be used to bond broken plastic items. Its advantage over glue is that it can bridge larger gaps and can be shaped or moulded to replicate the part of an object that is missing or has been destroyed. Most epoxy putties can be cut, shaped, and sanded when cured and can hold a screw or bolt.
How to use poster putty? ›
Adhere the putty to the item to be mounted. Mounting: Press the item firmly onto the mounting surface, such as a wall or a container. Removal: Remove the putty carefully by peeling it from the surfaces.
What is the ratio of putty to water? ›
The general rule of thumb is two parts white cement putty and one part water (2:1). However, refer to the manufacturer's instruction. The goal is to get a peanut-butter-like consistency. Apply first coat of putty: Let it dry for at least 6-8 hours (in case of cement putty).
How do you calculate wall putty material? ›
Wall putty coverage = 14 square feet per kilogramme for two coats. Needed wall putty: 2000/14 = 143 kg. One bag of wall putty weighs 40 kg, and since 143 kg is equal to 143/40 kg, 3.58 bags of wall putty are required. One bag of wall putty costs 800 Rupees.
What happens if the putty is too thick? ›
Avoid overcoating: The maximum thickness of wall putty that should be applied to the wall is 1.5 mm. The thicker coating may lead to cracks and peel-off.
How many coats of primer on putty? ›
Cement Putty applied in 2 coats then sand it to a smooth finish using 120 no sandpaper. Apply 1 coat of cement primer. Apply 2 or 3 coats of top coat paint.
